TECH CAPACITY : T:150X450

Manual machine, no automatic feed (with grindstone head up / down fast forward), T: 450 * 150 (17mm T-groove * 1), S: 480 * 180, Maximum distance from the top of the table to the center of the grindstone shaft 550, Distance from floor to work surface 1055, Table left and right handle 1 rotation stroke 100, Front and rear handle 1 rotation stroke 4, Front and rear handle 1 scale stroke 0.02, Forward / backward fine movement handle 1 scale stroke 0.001, Up and down handle 1 rotation stroke 1 Up and down handle 1 scale stroke 0.005, Vertical fine movement handle 1 scale stroke 0.001, Vertical fast forward speed 500mm / min, Whetstone dimensions: outer diameter φ205 * width 6.5-25 * inner diameter φ31.75, Grindstone rotation speed 0-2850 rpm (with inverter), Motor: 1.5kw2P for grindstone shaft (optional), 0.1kw6P for vertical fast forward, 13w for lubrication pump, Table drive method: wire, Table slide surface: sliding surface (turkite) * Vertical / front / rear digital dust absorption / water injection device (paper filter) Currently without magnet chuck (standard chuck dimensions: 350 * 150 * 70 / maximum work weight 70 kg)

TECH CAPACITY : T:400X900

T: 900 * 400, S: 1050 * 440, Flat chuck 900 * 400, Wet, Whetstone: 305 * 32 * 76.2

Many accessories such as Magsepa High-end product Grindstone rotation speed inverter With separate work loader type before and after the main body (Although it is a single unit separate interlocking specification, it can be easily separated when not in use and the main body is a normal specification as a general-purpose machine)

Through type Whetstone dimensions: φ455 * 150, Capacity : φ1 ~ ?75, Grindstone hydraulic bearing Adjusting vehicle hydraulic pressure bearing Adjustment car table slide static pressure guidance Lead screw Ball screw Coolant paper filter type.

Whetstone dimensions: 510 * 205 Whetstone shaft Adjustable axle co-static pressure Coolant device (with magsepa)

Grinding capacity: ?1.5-110mm Grinding wheel: ?510 * 205 * ?30 4.8mm Peripheral speed: 2000m / min Adjusting whetstone: ?255 * 205 * ?127mm 18-200 rpm (60 Hz) Infeed

Fines supply device (with FP straight feeder), Sulfeed grinding table for fines, supply pipe receiver / discharge shooter, grinding fluid purification device magnet separator (40 liters), reversing device and hanger for replacing both grindstones, water shield cover

2008 Manufacturer overhaul Grinding capacity: ?1-60mm Grinding wheel: ?405 * 150mm Adjusting whetstone: ?230 * 150mm 1450rpm

2021 OH finished Processing diameter: ?3-100mm Grinding wheel: ?610 * 305 * 304.8mm Adjusting whetstone: ?330 * 305 * 203.2mm Turning angle: (Feed angle) -1

Through feed Whetstone diameter: 455 * 150 Coolant device (Spiclon type) Diamond wheel Jib crane

* O / H at the manufacturer in 2005 Workpiece ??Diameter ?1mm ? ?50mm ??Maximum grinding length (in feed) 150 mm Grinding wheel ??Dimensions: Outer diameter ?455 * Width 150 * Inner ?228.6mm ??Peripheral speed 2400m / min Maximum peripheral speed 2700m / min Adjusting whetstone ??Dimensions: Outer diameter ?230 * Width 150 * Inner ?101.6mm ??Rotation speed 23-200 rpm (continuously variable transmission) motor ??Grinding wheel: Standard / 7.5kw Maximum / 15kw Adjusting wheel 0.75kw Hydraulic pump 0.4kw ??Grinding liquid pump 0.15kw pump ??Hydraulic: Type / Vane pump capacity 3L / min ??Grinding liquid: Type / External fan type Capacity 80L / min Lubrication ??Sliding surface: Manual lever pump Grindstone shaft: Grease worm gear: Oil bath Turning angle ??Adjusted vehicle feed angle + 6

Whetstone: ?610 * 205mm Through feed No separator and coolant tank

Whetstone dimensions: ?455 * 150 * ?228.6 (outer diameter * width * inner diameter) Grindstone peripheral speed: 2400m / min Adjustable vehicle dimensions: ?305 * 150 * ?177.8 (outer diameter * width * inner diameter)

Whetstone: 610 x 52 x 304.8mm, Processing diameter: 1-50mm, Rated Voltage : 200V, No load rotation speed : 1400 rpm, Grinding wheel dia : 610mm, Grinding wheel thickness : 52mm, Grinding wheel hole dia : 304.8mm.

Whetstone 610-220 Stop polishing product Both center holders move up and down

TECH CAPACITY : Φ:200X300

full automatic φ200 * 300 Maximum processing diameter φ60 Scale 1 axis

Chuck work surface : 900x400mm, Table left/right movement amount : 1050mm, Column longitudinal movement : 440mm, Grinding wheel spindle overhead vertical movement : 325mm, Distance between the center of the grinding wheel shaft and the top of the table : 175-500mm.

Table size : 1200 x 500mm, Width x height x length : 1200 x 600 x 500mm, Movement of table left and right : 1300mm, Movement of table front and back : 530mm, Top of the table : 850mm, Chuck dia : 600 x 500mm, Grinding wheel dia (dia x width x hole dia) : 510 x 50 x 127mm, Weight : 6500 kg.

Table : 1500 x 700mm,

Table size : 2050 x 800mm, Processing range (length x width x height): 2000 x 800 x 695mm, Stroke : Front/rear 860 x Left/right 2250mm, Grindstone: Outer diameter : 510 x 50mm, Inner diameter : 127mm.

Table size : 2050 x 500mm, Machining range of workpieces : 2000 x 500 x 595mm.

Machining range of workpieces:4000*800*800 Table:4050*800 chuck dimensions:4000*800*100 Loading weight:3728kg T-groove width*number:20mm*3 S:4250*800*860 Whetstone:?510*100*?203.2 (50/60Hz)1000/1200rpm,SIZE : W11*D4.5*H3.78m, WEIGHT : 30T

Fanuc-0M 1500rpm T:2000*600*83(H) S:2300*660*620 Grindstone diameter:?510*50*?127(inner diameter)

Vertical axis,T:900*400

Fanuc-20F T:580*200mm Chuck:500*200*70mm X:600 Y:225mm 3600rpm